The Italian coffee maker has been around for more than 80 years and is still the best in many ways: it’s cheap, simple to use, and stays brand new for a long time with little upkeep. Cleaning the Italian coffee maker after each use is an important part of this upkeep.
There are many false beliefs about How to clean your Italian coffee maker? One example is that soap should not be used. cleaning an espresso maker, you just have to follow these 10 steps:
How to clean your Italian coffee maker?
These easy steps will make it easy to clean your Italian coffee maker. First, take the coffee maker apart and take out all of its parts. Use warm soapy water to rinse each part. Scrub away any tough coffee dregs with a brush. Clean each part well with clean water and dry it all the way through. Run a brew cycle with equal parts water and vinegar to get a better clean. It’s then important to use clean water several times to get rid of the vinegar smell. Use a wet cloth to clean the outside of the coffee maker. After putting the parts back together, your Italian coffee maker will be clean and ready to make coffee again.
1. Separate the Parts
The first thing you need to do to clean the coffee maker right is to take it apart and empty it of any coffee leftovers or filter grounds. To do this, we need to take everything apart. The flat handle of a spoon can help us remove the rubber that holds the top part to the filter cup. The coffee maker’s bottom part, the coffee pot, the foam, the filter, and the top part are all in this order.
2. By hand or in the Dishwasher
Just as hand washing is suitable for all coffee makers, the same is not true for the dishwasher. Only some stainless steel coffee makers are suitable for this appliance. If this is the case, you have to put the parts separately inside the device and that’s it.
In the case of cleaning by hand, there is not a big difference between how to clean a stainless steel coffee maker and an aluminum one. We must keep in mind that we cannot use abrasive products because the two materials can be easily scratched. A soft scouring pad, the blue one, is suitable for all types of materials, even for cleaning the filter of a drip coffee maker.
3. Soak
Putting all the parts of the coffee maker in hot water with some soap for a few minutes can help you clean it more easily. This makes the dirt softer, which makes it much easier to get rid of without having to scrub too hard. We learned this trick in “how to clean an aluminum coffee maker,” and it works great when the gunk has stuck more than usual.
4. The Lower Container
This is where you put the water to make the coffee. Most of the time, it’s enough to wash it with warm soapy water, rinse it well, and let it dry. The base can sometimes catch fire because it is the part that comes into touch with the heat. This mostly happens when we use it on a gas stove.
The best way to clean a burned Italian coffee maker is to put the damaged part in a container with water, vinegar, and baking soda. Then, heat the container until it boils. Now that it’s been sitting for a while, we can clean the coffee maker made of aluminum or stainless steel by rubbing the base in rounds. There is a lot less damage to the burned parts.
5. The Filter Bucket
The ground coffee goes in this funnel-shaped part. Because of this, coffee dregs can often stay in the filter’s small holes. We can scrub the filter of the Italian coffee maker with warm water and soap, but we can also use a brush and lightly tap the base of the filter to get rid of any leftover dirt.
6. The Rubber
The rubber is essential for the correct functioning of the coffee maker and we often forget about it. It is important to clean it after each use with soap and water, without rubbing too much. If we observe that it has a greenish, yellowish or grayish color, it must be replaced with a new one.
Read More: How to clean farberware coffee pot
7. The top filter
The rubber-attached part at the base of the upper part is very important because it keeps the coffee grounds from mixing with the liquid. That’s why we need to be very careful when we use a brush to clean this filter and get rid of any coffee that might still be in it.
8. The Top
This part, which gets the hot coffee, needs a little more care when it comes to cleaning than the bottom part. Before you scrub it with soap and water, you should let it soak for a little longer to soften the coffee residue. The standard Italian coffee maker model is shaped like an octagon, which makes it hard to get to many angles because the pipette is in the middle. A good tip is to clean it with a toothbrush that is only used for that job.
9. Drying
To clean an Italian coffee maker made of metal or stainless steel, it’s important to rinse and dry it. It’s important to rinse everything really well to get rid of any soap that might make the coffee taste bad. The parts of the coffee maker need to be dried before they can be put back together. Letting them dry in the air is best.
10. Depth Cleaning
Even if you clean the coffee maker often, some stubborn residues may build up over time and need to be cleaned completely. We might also have to clean a metal or stainless steel coffee maker that is on fire inside. Because of this, we know the best way to clean the inside of an Italian coffee maker.
The lower jar is filled with equal parts water and vinegar. The coffee maker is then put together without any coffee in the filter. We turned on the coffee maker’s heat and let it do its thing before it was turned off. After the vinegar water has cooled, we empty it, take it apart, and wash the parts with soap and water.
These 10 steps help us keep the old Italian coffee maker clean and in great shape so it can keep making the best coffee. Also, follow these easy steps to make the best coffee in your Italian coffee maker.
Read More: How to clean Farberware coffee maker? Easy Tips For Beginners
